The first step to doing this is installing a basket strainer. A basket strainer replaces the sink flange of the garbage disposal.
There are many make and models of sink basket strainers. Make sure that the sink is clean and dry. Insert the strainer into the sinkhole and press it tightly. A sink strainer is fitted to the sink using a lock nut. It also comes with a rubber and a cardboard gaskets. So, get underneath the sink and put the gaskets in place as per its installation manual. Then tighten the lock nut using your hands until it touches the gaskets.
Once the lock nut is somewhat tight, use a sink strainer tool or a channel-lock plier to tighten it. You can use an installer tool or a needle nose plier to hold it in place. Once the sink strainer is installed, connect a tailpipe to it. This length can be cut as required for drain pipe installation. If you followed all the directions above, you are now left with a discharge tube and the rest of the plumbing if yours were a double sink, or a p-trap and the rest of the plumbing if yours were a single sink.
What we are going to do here is connecting the existing drain pipes to the tailpipe from the sink strainer. For this, we need a coupling elbow. If the elbow is not long enough, you will have to replace this drain pipe with a new one. Measure twice and cut once.
Make the connections and make sure that every joint are properly sealed with washers. You do not need to install double p-traps; a single one will do. If yours were a single sink, then the p-trap and the drain pipe going into the wall is what is left of the old plumbing. The p-trap needs to be connected directly to the tailpipe from the sink. Take the necessary measurements and size the pipes accordingly. Once the whole replacement is done, run lots of water into the sink to check for any leaks.
Make sure to use sealants wherever necessary. The reason why people choose not to have a garbage disposal varies. Some people choose to compost their food wastes which is a more environmentally friendly way than using a garbage disposal.
Some are tired of constant clogs in the disposal and the hassles of maintaining it. But many people who choose to get rid of garbage disposals do so because they messed up the plumbing system. Many try to remodel their kitchen themselves, and a trendy thing now is the use of deep sinks like farmhouse sinks. The problem with installing deep sinks is that the plumbing needs to be lowered for the drain pipes to work.
More often than not, the additional space needed for the garbage disposal with the already lowered sink leaves no room for the plumbing to be lowered. Cities like New York—along with many governments in Europe —banned disposals altogether, arguing that the added food waste would overtax the water-treatment system.
Whatever stuff gets separated from the water is either landfilled, condensed into fertilizer, or digested by microorganisms. Garbage Disposals Can Manage Grease In the garbage disposal, these can build up in the pipes and the system itself. This hampers the ability of the disposal to grind the food and creates blockages or narrowed pipes that can stop the food and water from moving through the system. Disposal is a universal tool for garbage disposal installation and removal; it makes installing a kitchen disposer much easier; it lifts and holds for easy installation and removal: replace a disposal without the risk of strain or injury.
Dr Disposal is small — light weight and fits easily into your tool pouch. Tools Replacement Garbage Disposal. Electrical Cable Connector. Needle Nose Pliers. Wire Nuts. Wire Stripper. Most disposals have a life expectancy of about 10 years, after which they may start clogging more often. Prices vary based on which unit you choose, as well as who you hire for the project.
Here are 7 things you should not put in a garbage disposal: Coffee Grounds. Eggshells in Disposal. Onion Skins. Potato Peels in a Garbage Disposal. Hard Foods. This applies to people with an old faulty unit that they want to replace with a new unit installed to a double sink.
Carefully disconnect the old unit starting with the disconnection of the electrical parts. Proceed to detach the drains connected to the disposal and then detach the unit from the flange.
Before proceeding, you will need to disconnect the disposal flange mounting from the sink drains. You, however, can still mount it on this flange if you are installing a disposal unit from the same brand.
Some experts are likely to advise to replace it all the same for a better sealing of the drain. Disconnect the discharge tube and the entire drainage system from the second sink.
You can do this if the tailpiece, the tee, and the drainage tube are faulty. If it does not experience any leaks, however, there is no need to replace it. The preparation process of installing a disposal unit to a double sink is slightly different if you have to prepare the second sink differently.
When working with a sink that will hold the disposal unit, you can follow the process we mentioned above. Seal the sink flange with silicon because you can rely on it to seal off leaks since it sticks securely in place.
While holding the tailpiece into place, turn it in a clockwise direction until it fits securely under the sink. Follow this with a tee and connect it to the tailpiece. The tee will allow you to attach the discharge tube to the disposal unit in the first sink. Prepare the discharge tube by first connecting it to the already mounted disposal unit. Mark it right at the correct measurement and cut it with a hacksaw for a perfect disposal installation. You can then loosen the discharge tube from the disposal unit so that you can insert it to the tee before reconnecting again.
Once you are sure that you have mounted the garbage disposal on the first sink securely and the second sink is well fixed, now is time to connect the electrical wires. Removing the wire cover plate, get the wires to match according to their respective colors.
Afterward, insert the wires back and then reattach the cover place for safety. Attach the discharge tube with the flange and the screws or bolts. Using a hammer and screwdriver, unblock the dishwasher drain before connecting it. Testing allows you to confirm whether your installed unit works. Simply fill both sinks with water and run it to check for leaks. You can then switch on the unit by plugging in the power cord.
Installing a disposal unit to a single sink is even simpler as compared to installing the unit to a double sink. Here are the simple steps to follow whether you are replacing an old fault disposal or installing a new one.
Unplugging the power cord will ensure your safety by protecting you from electrical shocks. Before you disconnect the drains, put a bucket under the sink in order to trap water that might still be within the drains.
Detach the drains as well as the strainer. Assemble the fiber gasket, the backup flange, and the mounting ring in that order and then slip them onto the flange.
Pull the snap ring to open it in order to fix it into place easily. Thereafter, tighten the screws in an even manner for a secure fitting on the backup flange. Make sure you clean off the leftover putty. Connect the dishwasher drains to the disposal unit by first unblocking with a hammer and a screwdriver.
Before unblocking, remember to remove the plug from the inlet of your disposal unit. Connect the power cord by removing the cover plate and matching the wires with their respective colors before reattaching the cover plate. Now it is time to install the entire disposal unit under the sink.
You can do this by inserting the gasket to the discharge outlet, connecting the discharge tube to the flange, and screwing the bolts for a firm fitting.
Align the three taps of the disposal with the mounting ring. Using a wrench, turn and lock the taps securely over the ridges. Connect the dishwasher drain and make sure the discharge tube is fixed properly before connecting the other drainpipes. Before you fold your tools to go, make sure you have tested the disposal unit to ensure it is working properly.
Moreover, check for any leaks by running water from an already filled sink. The process of installing a badger disposal unit only requires you to have a few tools and the materials needed. Check out the simple steps below! Before you even start installing your badger disposal unit, make sure the place under the sink is clean.
0コメント